As much as we’d love to believe that it is, the old D4D HiLux certainly isn’t unbreakable or without problems. Thankfully, we’re here with a heads-up on common problems and solutions for your D4D Toyota Hilux.
In 2005, Cardinal Joseph Ratzinger was elected as the new Pope, The Prince of Wales remarried after Lady Diana to Camilla Parker Bowles, and the 1KD-FTV motor hit our shores. Unlike The Prince of Wales’s marriage, the news was received well by the masses, and there was an extremely warm reception. We were stoked to finally have a HiLux with a decent amount of performance. This was thanks to the high-tech (for the time) 3.0-litre turbo-diesel motor and independent suspension featuring a coilover strut in the front end that rode well for a work ute.
Like all good things, the veil was soon shattered as we realised the D4D Hilux, unfortunately, had a number of common problems. With clutches burning out prematurely, injectors causing issues, and cases of holes being melted through pistons, things weren’t great. However, time both heals wounds and clues you up as there are now fixes available for these problems. It’s worth mentioning that these fixes are more affordable than they have ever been. Thank us later, as the research has been done. I’ve got 99 problems, but a blown D4D won’t be one… knock on wood.
Problem: Injector seals and seats
We hate to welcome you to the epicentre of common problems for the D4D HiLux motor, but here it is. Shithouse injectors and seals cause a flow-on effect of issues for your vehicle. How come? Well, the original injector seats at the base of the injector were made from copper, which would fail regularly. You may have actually heard of the recall that was announced for this in New Zealand and Europe. Us Aussies seemed to have been left off the email chain for the recall service.
When the seats go, you’ll find that excess blow-by gases enter the tappet cover. This mixes with the engine oil, creating carbon. This then blocks the oil pick-up which results in a motor starved of oil. Experiencing white smoke and a rattling noise when cold? This is likely your culprit.
The injectors are under enormous pressure from the common-rail injection system and are prone to failure. Make sure you’re getting them checked every service to see if they are operating within spec. It’s also recommended that they’re replaced every 100,000km. Listen out for loud knocking, as this could be poorly performing injectors. They’re also known to present a poor idle and poor fuel economy. They are responsible for cracking pistons, which is another common problem with the D4D HiLux motor.
Solution:
When we present you with the bad news of a problem, we will always soften the blow with a solution. A geez online shows an injector kit from a reputable brand will set you back a couple thousand just in parts. For the majority of us, this is a huge blow to the wallet. Unfortunately, an expensive fix to this common D4D HiLux problem.
If the injectors are still in spec, it is advised to change the seats with new diamond-like coating seats, which were introduced in 2007 every 40,000km. Change the injectors every 100,000km as well. This will prevent cracked pistons, clogged oil pick-ups, and other associated issues that were mentioned previously.
Problem: Engine rattle
You’ve likely heard that D4D HiLux engines have a famously common problem – they’re noisy. This is exacerbated when cold, which makes winter a whole lot of not-fun. This noise could be a few things, with many reports that the injectors are again the culprit. This is usually the main spindle in the centre of the injector sticking to the bore of the injector. The tolerances are finer when cold, and friction levels are higher. This is why the injector holds open for longer, which introduces potential over-fuelling issues.
Another theory is that the noise comes from the rockers, which, when the engine has just started, haven’t had the chance to be properly lubricated. The solution here is to always use good quality oil as well as take it easy for the first 5-10 mins of driving. Our advice is to take it easy, and if in doubt, see a diesel specialist and have your injectors inspected. This is ideal to see if they are still within spec.
Solution:
Make sure that you’re using good-quality oils in your D4D HiLux engine and that you change them regularly to help out with this common problem. Consider changing them every 5000 kilometres. Valves should be inspected every 40,000 kilometres. Sadly, adjustment is quite involved, thanks to the bucket and shim design. Have your injectors inspected regularly and have the seals replaced every 40,000 kilometres. A decent mechanic will be able to test the injectors to see if they are still within spec.
Problem: Turbo stepper motor
The turbo fitted to the 1KD is a variable vane design. It’s controlled by an external turbo actuator stepper motor rather than a traditional dump valve and pneumatic wastegate. The stepper motor controls the angle of the turbo vanes that dictates boost levels. These can and often do fail in the D4D HiLux motor – a frustrating common problem. Why? This is what causes fault code P1251 (34) and the vehicle going into limp mode. What does this result in? You’ll find the vehicle can’t rev past 1500rpm.
Solution:
If you were in this situation a few years ago, replacing the entire turbo would be recommended as a solution to this common D4D Toyota HiLux problem. Thankfully, you can now buy the stepper motor separately for much less. Alternatively, you could use this opportunity to upgrade the turbo if you’re looking for more performance. Keep in mind this will cost more than the replacement stepper motor.
Problem: Dodgy clutch
Another common problem is reports of clutches slipping on the D4D Toyota HiLux. There have even been yarns of some needing replacement in as little as 20,000km. Driving style and load play a massive part in clutch wear, so it’s something to be aware of when buying a used HiLux. Factor in the cost of a clutch replacement, basically.
Solution:
We’re sorry to say that the only way out is to fit an upgraded clutch and have the flywheel machined. A sympathetic driving style will go a long way in getting longevity out of your clutch.
Problem: EGR blockage and soot
This is a problem for all common-rail turbo diesels (not just your D4D HiLux) with an EGR (exhaust gas recirculate) valve, where oil and mist-laden exhaust gases are fed back into the engine in an attempt to reduce emissions. This process is what causes carbon or soot to build up in the EGR valve and intake of the motor. It reduces performance and essentially chokes it up. The HiLux is prone to this, and the fix is typically an expensive teardown and clean of the intake system.
Solution:
Fit an oil separator as soon as possible to trap oil mist from the exhaust gas before it’s fed back into the turbo. If you have done a lot of kilometres in your vehicle and haven’t fitted a catch can, it would be advisable to have your intake and ERG inspected. This helps to see how messy it is. Cleaning it is extremely laborious, and the right way to do it. However, you’ll need to decide whether the idea of a chemical carbon clean on the vehicle is something you’d want to do. Some people blank off their ERG with a metal plate. However, this is illegal for road use. Definitely don’t do that.
Problem: Engine seized
This is as bad a common problem as it gets for your D4D HiLux engine – or any engine for that matter. Essentially, it decides it’s had enough of life, and it throws in the towel. The D4D isn’t immune to seizing, however it’s definitely avoidable if you know where to look. The problem is caused by the oil pick-up in the sump becoming choked up with carbon and debris. This then restricts the oil flow and destroys any chance of the motor getting vital lubrication. This comes back to those pesky injectors. When the seal fails, oil and carbon gases leak into the cylinder. This concoction then thickens the engine oil and blocks the oil pick-up. Ultimately, this cuts off the flow of oil.
Solution:
Engine oil changes need to be performed on time, every time they’re due. When the sump drain plug is removed, make sure to shine a torch up through the hole. This will help you to visually inspect the pick-up mesh. If there is anything other than oil on it, you will need to drop the sump and clean the pick-up mesh. It is also time to have the injectors inspected and the seals replaced, as this is causing the issue. Well, unless you just haven’t changed the engine oil ever, then there are more problems with your motor than modern engineering can solve.
Problems: Water pumps leaking prematurely
Water pumps leaking prematurely in your D4D HiLux are another common problems and are a sign they have had it. The parts themselves aren’t too expensive, but while you are in there, you may as well replace the timing belt. You may as well check the injectors if the condition is unknown, and then you may as well have the valves checked for correct adjustment. You may as well change the drive belt too, and check to see if any of the idler pulley bearings are going crunchy and replace those as well.
Solution:
Replace water pumps before 150,000 kilometres, or just do them when you change the timing belt. Hopefully, they aren’t leaking, but a sure sign would be coolant seeping from the water pump or sprayed up around the engine. If your coolant level is low, but your hoses aren’t leaking, this is a good place to look. While changing the water pump is fairly straightforward and relatively inexpensive, it’s the flow-on effect of all the bits you might as well fix while you are there that will add up.
Words: Evan Spence and Jess Olson
would be good to see a similar article on ford??
This was covered for the Ford previously. Assuming you are a Ford owner and want to know some preventative maintenance tips like Toyota owners do? I have owned both and have appreciated the benefits of shared knowledge from the brains trust👌.
https://unsealed4x4.com.au/ford-ranger-3-2l-common-problems-and-solutions/
“They are responsible for cracking pistons, which is another common problem with the D4D HiLux motor”
Maybe so, but TOYOTA are are also responsible for manufacturing FAULTY PISTONS in the HILUX & PRADO engines.
A problem that they, TOYOTA, will bear NO RESPONSIBILITY for!!